|
|
Joined: Feb 2012
Posts: 715 Likes: 16
Paranoid android
|
|
Paranoid android
Joined: Feb 2012
Posts: 715 Likes: 16 |
Hello Maybe you should try this power supply: 60W SMPS It is physically the same size but is rated a bit higher so should run cooler and hopefully last longer. Neil
1) MS200, G65, Revivers, DSP5000.2, DSP5000C.2, DSP3100, D1500, SME10/IV.
2) Mac Mini (Roon), Explorer 2, Sennheiser HD6XX.
|
|
|
|
|
Joined: Jun 2009
Posts: 121 Likes: 2
Hitchhiker
|
|
Hitchhiker
Joined: Jun 2009
Posts: 121 Likes: 2 |
Neil
Many thanks for the advice. In fact that is the one I fitted two years ago, so perhaps I have just been unlucky. Story of my life.....
Regards Paul
Paul Lounge: DSP8000SEs, G65, 218, 204 FM tuner Family room: DSP6000s, G91, Soolos MediaCore 200 Roon Nucleus+ serving both systems Unused: 861v4, G68,500 series CD/preamp. John Bowers Active 1 loudspeakers
|
|
|
|
|
Joined: Oct 2008
Posts: 198 Likes: 1
Hitchhiker
|
|
Hitchhiker
Joined: Oct 2008
Posts: 198 Likes: 1 |
Are you sure it's actually the power supply?
I replaced the power supply in a G68 and it 'failed' again after a few months.
On further investigations, it was the metal contacts in the plug that plugs onto the power supply pins, one of the 5v contacts was carbonated and black.
I bought some better quality crimp on contacts, refitted them to the cable, plugged in the 3 month old 'failed' PSU and it's been fine for the last 4 years!
Main: 861v4, UHD722, 558, Klipschorn, SVS PC13u second: Tom Evans Eikos, DCB1-pre, DIY Nelson Pass PLH amp, DIY speakers.
|
|
|
|
|
Joined: Jun 2009
Posts: 121 Likes: 2
Hitchhiker
|
|
Hitchhiker
Joined: Jun 2009
Posts: 121 Likes: 2 |
Grog
Thanks for that suggestion. I will check it out. I assume it is the contacts on the plug that takes the 12v and 5v feeds from the PS to the rest of the G68?
Paul
Paul Lounge: DSP8000SEs, G65, 218, 204 FM tuner Family room: DSP6000s, G91, Soolos MediaCore 200 Roon Nucleus+ serving both systems Unused: 861v4, G68,500 series CD/preamp. John Bowers Active 1 loudspeakers
|
|
|
|
|
Joined: Oct 2008
Posts: 198 Likes: 1
Hitchhiker
|
|
Hitchhiker
Joined: Oct 2008
Posts: 198 Likes: 1 |
Hi Paul, Yes the metal contacts that clip into the white plastic plug housing, which in turn comments to the row of pins on the PSU with 5v, 12v etc. The contacts on the end of the wire harness from the G68 motherboard. You can see here, one of the problems with the standard connector pin is that it's only touching 1 side of the PSU pin, you can get pins similar size that are like a box section, they contact on all 4 sides of the PSU pin. On the second, slightly blurred picture, you can see the blackened contact area. ![[Linked Image from gallery.seloc.org]](http://gallery.seloc.org/albums/userpics/27715/G68-pin2.JPG) ![[Linked Image from gallery.seloc.org]](http://gallery.seloc.org/albums/userpics/27715/G68-pin1.JPG)
Main: 861v4, UHD722, 558, Klipschorn, SVS PC13u second: Tom Evans Eikos, DCB1-pre, DIY Nelson Pass PLH amp, DIY speakers.
|
|
|
|
0 members (),
142
guests, and
2
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums18
Topics31,150
Posts296,944
Members5,503
| |
Most Online4,788 May 22nd, 2026
|
|
|
|