#277265 - 2018-06-19 09:17
FS: Linear Power Supply 230v PSU for an 861v4
|
Registered: 2015-12-16
Posts: 17
Jackylong
Harmless
|
Harmless
Registered: 2015-12-16
Posts: 17
Loc: Shanghai, China
|
Hi,
My 861 has a Linear Power Supply, but it is 110V.
I am looking to replace it with a 230v PSU ... I do not need the LPS Board.
Thank you.
861v4, HD621, MC200
|
Top
|
|
|
#277269 - 2018-06-19 09:38
Re: FS: Linear Power Supply 230v PSU for an 861v4
[Re: Jackylong]
|
Registered: 2016-11-27
Posts: 197
Struttmaster
Hitchhiker
|
Hitchhiker

Registered: 2016-11-27
Posts: 197
Loc: Gold Coast, Queensland, Austra...
|
I have a switched PS that was in an 861v6, it was replaced with a linear.
HT: G68ADV w/LPS, HD621, DSP5000 F&C 24/96, DSP3100, Allo digi Office: Fanless 7i5 running ROCK, 218, Woo Audio WA2 (w/50yo Tung-Sol tubes), Focal Utopia Family Room. Grandinote Volta, Ultra rendu w/LPS 1.2, Prime with PSU, Grandinote Shinai Bedroom: MRendu w/IsoREGEN, 568.2mm, 598, 3100C BBQ/Party: Raspberry Pi, Explorer 2, F80
|
Top
|
|
|
#277408 - 2018-06-21 14:35
Re: FS: Linear Power Supply 230v PSU for an 861v4
[Re: Struttmaster]
|
Registered: 2015-12-16
Posts: 17
Jackylong
Harmless
|
Harmless
Registered: 2015-12-16
Posts: 17
Loc: Shanghai, China
|
I have purchase a old switched PS As a spare.
But I still want to continue using a linear power supply, which are better for analog output.
Thanks
861v4, HD621, MC200
|
Top
|
|
|
#277411 - 2018-06-21 17:47
Re: FS: Linear Power Supply 230v PSU for an 861v4
[Re: Jackylong]
|
Registered: 2000-06-08
Posts: 290
Marc Koval
Hitchhiker
|
Hitchhiker
Registered: 2000-06-08
Posts: 290
Loc: Dglv, Georgia, USA
|
I have sent this to you previously:
Attached to messages about purchasing the E/F Card.
....
Let me know if you want me to get you the 220 V transformer for your existing Linear Power Supply (the one part you need to change to modify the input voltage) that way you can keep the improvements for the sound and use local power. It is not hard for a technician to replace, only 2 wires need to be soldered and a few screws...
.....
If you switch back to a universal switch mode PSU. You WILL need the Distribution board as well as the PSU assembly.
OR
You can just swap out the mains transformer on the LPSU that is currently in the unit.
Marc Koval The Repair Shop 404-585-1102 marc<at>the-repair-shop<dot>com
|
Top
|
|
|
#277440 - 2018-06-23 12:41
Re: FS: Linear Power Supply 230v PSU for an 861v4
[Re: Marc Koval]
|
Registered: 2015-12-16
Posts: 17
Jackylong
Harmless
|
Harmless
Registered: 2015-12-16
Posts: 17
Loc: Shanghai, China
|
Hi, Marc Koval
I have send a email to you.
Thanks
861v4, HD621, MC200
|
Top
|
|
|
|
4,723 Registered Members
18 Forums
25,926 Topics
260,863 Posts
Most users ever online: 211 @ 2015-05-05 14:40
|
|
|