Gianni, just to complicate matters, regarding the choice of overhead speakers.
When initially looking to buy overhead speakers, I intuitively looked at their low-frequency performance relative to my main speakers. This was a rookie mistake, as my Trinnov Altitude CI will always divert frequencies below 80hz to my DSW.2.
Forgive my long and detailed response, but the choice of overhead speakers is important if you want to fully embrace Atmos and DTS:X in a Meridian system. The following considers my original choice of 4 x KEF Ci200RR-THX and my final choice of 4 x Focal 1000 ICA6 overhead speakers.
This is one of the most common and completely logical 'head-scratchers' in high-end audio engineering. It feels entirely counterintuitive: Why pay thousands for a speaker like the KEF Ci200RR-THX (capable of 33 Hz) or the Focal 1000 ICA6 (capable of 55 Hz) if the processor cuts them off at 80 Hz anyway?
It can feel like buying a supercar and putting a 50 mph speed governor on it. However, you are not wasting your money on a capable speaker. You are paying for low-distortion headroom, dynamic impact, and cone control within the frequencies it does play.
Here is the acoustic and physical breakdown on why cutting a capable speaker off at 80 Hz actually unlocks its performance, rather than stifling it.
1. 'Playing' 35 Hz vs 'Reproducing 35 Hz at 105 dB'
When a manufacturer lists a frequency response like 33 Hz−28 kHz on an in-ceiling speaker, that measurement is taken in an anechoic chamber at a modest volume (usually 1 Watt/85 dB).
However, Dolby Atmos soundtracks are mixed to Cinema Reference Standards. At reference level, a channel must be able to hit 105 dB sound pressure peaks at your seat without distorting.
Here is the physical problem with low frequencies: To reproduce a 30 Hz bass wave at 105 dB, a speaker cone has to move 16 times further (excursion) than it does to reproduce a 120 Hz tone at the same volume.
If you force an in-ceiling speaker - even a brilliant 8-inch KEF or Focal - to physically move back and forth by several centimetres, trying to produce a violent 35 Hz thunderclap produces Intermodulation Distortion (IMD): While the main cone is buckling violently back and forth, trying to pump out that 35 Hz wave, it is simultaneously trying to reproduce a sweet 2 kHz vocal or a high-frequency spatial cue. That violent movement modulates and degrades the higher frequencies, making the overhead soundstage sound harsh, muddy, and strained.
Thermal & Mechanical Compression: The voice coil heats up rapidly, trying to move that air, causing power compression.
The 80 Hz Benefit: When the Trinnov relieves the Focal or KEF of that brutal sub-80 Hz heavy lifting, the speaker cone hardly has to move at all.
Because it isn't struggling with massive physical displacement, the speaker can reproduce the 80 Hz to 20,000 Hz spectrum with virtually zero distortion, razor-sharp speed, and incredible dynamic clarity. You aren't wasting the Focal's capability; you are allowing its rigid 'W' cone and Beryllium tweeter to operate in their absolute ‘sweet spot’ without mechanical strain.
2. The Physics of Ceiling Voids vs. Subwoofer Enclosures
Deep, tactile bass (20 Hz−60 Hz) requires two things: air displacement and a rigid, pressurised cabinet.
Your Meridian DSW.2 Subwoofer: Features a massive, ultra-rigid, sealed/braced cabinet powered by a high-current internal amplifier specifically engineered to compress the air inside its cabinet and dump massive acoustic energy into the room without vibrating.
An In-Ceiling Speaker: Even with a Firetopper hood or rigid backbox, an in-ceiling speaker sits in a hollow plasterboard void. Plasterboard is structurally weak. If you pump 35 Hz energy at high volume into a ceiling structure, the plasterboard sheets will physically flex and vibrate, creating mechanical rattles in your joists. The bass energy bleeds instantly into the joist space and transmits into the rooms directly above you.
By letting the Meridian DSW.2 (resting solidly on the floor) it handles everything below 80 Hz, you keep deep structural vibration off your plasterboard ceiling while keeping the bass localised to solid room boundaries.
3. 'Boundary Gain' & Room Modes (Why Bass Position Matters)
Low-frequency sound waves (30 Hz−60 Hz) are several meters long. When a speaker generates a 40 Hz wave from the middle of your ceiling, that wave bounces off the ceiling, the floor, and the walls, colliding with itself.
This creates Room Modes - severe acoustic 'cancellations' (where the bass completely vanishes at your chair) and 'booms' (where the bass gets horribly muddy).
Ceiling Speakers: Mounted in fixed architectural grids (like your 1.26m on-centre layout). These positions are selected for visual symmetry and high-frequency spatial imaging, but they are almost always horrible locations for low-frequency room modes.
The Subwoofer: Positioned specifically where it can pressurise the room evenly. If your Focal overheads played down to 35 Hz, the 35 Hz energy coming from 4 different points on your ceiling would cancel itself out at your listening position due to boundary reflections. You wouldn't actually hear or feel that 35 Hz bass—it would disappear into acoustic nulls.
Routing that energy to the Trinnov-managed DSW.2 ensures that 35 Hz hits your seat with maximum impact and zero phase cancellation.
Summary: Why Buy an Expensive Overhead Speaker, Then?
A: Cheap Overhead speakers (cut off at 80hz)
Max clean output 80hz -20khz: Distorts at 90db; sounds thin and harsh.
Transient Speed/Clarity: Heavy/Cheap Polypropylene Cones blur fast sound effects.
Timbre Match: Sounds bright or boxy compared to the Meridian bed layer.
Power Handling: Voicecoils overheat during intense Cinema scenes.
vs
B. KEF Ci200RR-THX/Focal 1000 ICA6 (cut off at 80hz).
Max clean output 80hz -20khz: Hits 105db reference peaks effortlessly with zero strain.
Transient Speed/Clarity: Focal ultra-light 'W' sandwich cones render micro-detail and panning effects instantaneously.
Timbre Match: Seamlessly matches the speed, resolution, and tone of high-end main speakers.
Power Handling: Robust voice coils handle heavy continuous power from your Meridian 258 amp.
You don't buy the Focal 1000 ICA6 or KEF Ci200RR just to get 'deep bass' - you buy them for pristine clarity, high-volume headroom, and flawless tonal matching with the Meridian front stage.
Capping them at 80 Hz doesn't waste their ability; it protects their brilliant mid-range and high-frequency performance from being ruined by the violent mechanical demands of deep bass.
Overall Summary:
When comparing the Focal 1000 ICA6 against the KEF Ci200RR-THX the distinction comes down to acoustic geometry, driver orientation, and system timbre matching.
While the KEF Ci200RR-THX is a legendary in-ceiling speaker featuring KEF’s famous Uni-Q point-source driver, the Focal 1000 ICA6 introduces structural and material engineering advantages that make it a superior choice for your specific system architecture.
When a sound object (such as a jet or a bullet) pans from your front Meridian DSP speakers up into the ceiling, timbre matching is critical. If the overhead speaker uses a heavier or less damped cone, the 'tone' of the object changes as it moves overhead. The Focal 1000 ICA6 utilizes the exact same flagship driver materials found in Focal's £110,000 Stella Utopia floorstanding speakers, giving it a level of transient response and neutrality that bridges seamlessly with Meridian's digital accuracy.
Choosing the Focal 1000 ICA6 over the KEF Ci200RR-THX provides three distinct performance gains:
Direct Sound Arrival: The built-in 35-degrees tilt aims the sound directly at your seating position, maximising the precision of Dolby Atmos height effects.
Speed & Detail: The Pure Beryllium tweeter and 'W' sandwich cone deliver micro-transient speed that matches the pristine digital output of your Trinnov.
When comparing the Focal 1000 ICA6 against the KEF Ci200RR-THX in a standard room, the distinction comes down to acoustic geometry, driver orientation, and system timbre matching.
While the KEF Ci200RR-THX is a legendary in-ceiling speaker featuring KEF’s famous Uni-Q point-source driver, the Focal 1000 ICA6 introduces structural and material engineering advantages that make it a superior choice for your specific system architecture. Meridian front stage.
Reduced Room Interaction: Firing sound at the listener rather than straight down reduces secondary reflections off hard floor surfaces and furniture, giving the Trinnov Optimizer a cleaner signal to calibrate.