|
|
Joined: Aug 2017
Posts: 93 Likes: 3
Hitchhiker
|
|
Hitchhiker
Joined: Aug 2017
Posts: 93 Likes: 3 |
hi steve when putting the cards back in should i follow the procudure in this tech note
Nuc Rock / G08 / Dual 5000 -> 818v3 -> 5200SE Nuc Rock -> Director -> 551 -> Dali Nuc Rock -> explorer-> F80 LG-TV -> G91A -> B&O 6000 & Loewe G98AH in life support G68ADV 💀
|
|
|
|
|
Joined: May 2005
Posts: 840 Likes: 161
Pan-dimensional being
|
|
Pan-dimensional being
Joined: May 2005
Posts: 840 Likes: 161 |
Hi Andy,
There's no harm in following the tech note. I always replace the capacitors on the backplane and check for any other suspects on all the cards (different models of G68 have different card combinations).
At least if they've all been replaced, the unit should work and last for another 10-15 years!
Cheers,
Steve
Main: 861v6 (LPS), 808v6, UHD722, DSP8000SE Anniversaries, DSP5200.2HC, DSP7200.2, SW1600, Sky Q, Cambridge Audio BD, Roon, M80 Office: 861v4 (LPS), 818v3, 800v4, HD621, M&K S150P, DSP5500HC, M&K MPS2810 sub x2 Son's system: 861v4, HD621, DSP6000.2, DSP5200HC, DSP33 Spare: MCD, 100 Series, 200 Series, 500 Series, F80s, C15s.
|
|
|
|
|
Joined: Aug 2017
Posts: 93 Likes: 3
Hitchhiker
|
|
Hitchhiker
Joined: Aug 2017
Posts: 93 Likes: 3 |
On inspection I also found this capicator looking suspicious - maybe not related to the humming output - but it might be a good idea to replace it I tried to get the board out but it seems attaced to the sceen and the volume knob, is there an easy way to get the board out ![[Linked Image]](gallery/16/full/4144.jpg)
Nuc Rock / G08 / Dual 5000 -> 818v3 -> 5200SE Nuc Rock -> Director -> 551 -> Dali Nuc Rock -> explorer-> F80 LG-TV -> G91A -> B&O 6000 & Loewe G98AH in life support G68ADV 💀
|
|
|
|
|
Joined: May 2005
Posts: 840 Likes: 161
Pan-dimensional being
|
|
Pan-dimensional being
Joined: May 2005
Posts: 840 Likes: 161 |
Ah... the usual bulging capacitor on the display board! It shouldn't be related to the hum but ideally should be replaced.
As it is almost impossible to get to the underside of the board (unless you fancy de-soldering the delicate vacuum display), I would leave the display in place, carefully cut the faulty capacitor off the board, de-solder the legs, and then insert a replacement capacitor slightly proud of the PCB (so you have enough room to solder the legs on the component side).
If you need to remove the display, there is a nut and washer behind the volume knob that needs to be undone. Be careful as it is also glued via a sticky pad to the front glass!
Good luck,
Steve
Main: 861v6 (LPS), 808v6, UHD722, DSP8000SE Anniversaries, DSP5200.2HC, DSP7200.2, SW1600, Sky Q, Cambridge Audio BD, Roon, M80 Office: 861v4 (LPS), 818v3, 800v4, HD621, M&K S150P, DSP5500HC, M&K MPS2810 sub x2 Son's system: 861v4, HD621, DSP6000.2, DSP5200HC, DSP33 Spare: MCD, 100 Series, 200 Series, 500 Series, F80s, C15s.
|
|
|
|
0 members (),
1,266
guests, and
3
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums18
Topics31,256
Posts297,490
Members5,503
| |
Most Online4,788 May 22nd, 2026
|
|
|
|