An overview of the tweeters used in Meridian’s flagship floor standing DSP loudspeakers.
SEAS OEM TWEETERS
Below are the the main tweeter variants utilised in floor standing DSP speakers. All are OEM units manufactured to Meridian’s unique specifications by SEAS of Norway. Unfortunately there are no longer available stocks of the earlier tweeters, Meridian recommend the use of the current '.2’ H1612 tweeter as a replacement. Do not be tempted to use a SEAS stock tweeter as they may be mechanically incompatible and certainly will not have the same frequency response.




25 TAFC/GW-BS H539 – 6 Ohm (Silver Dome)
Legacy DSP5000, DSP5000C, DSP5500, DSP5500HC, DSP6000, DSP6000VC and other older legacy. The original H539 cements the ‘Meridian Legacy’ sound, supreme politeness but with plenty of detail. There is no new H539 stock available.
25 TAFC/GW-BS1 H1054 - 6 Ohm (Black Dome)
Legacy DSP8000, DSP7000, DSP7200, DSP7200HC. The H1054 first appeared in the DSP8000 in Yr2000. A significant improvement over the H539, with higher power handling and along with the physical height increase when mounted in the DSP8000 integrated effortlessly to give a huge dynamic presentation. The H1054 was subsequently used in the DSP7000 and the first release of the DSP7200.
The H1054 can be used as a direct replacement for the H539. However, although they both have 6 ohm impedances the H1054 is more efficient giving a slightly higher output than the H539 and may require access to the loudspeaker “Calibration” menu, decreasing the calibration setting for the tweeter channel by a small amount (-1.0dB) , experimentation may be required. As of January 2021 Meridian no longer have any available H1054 stock.
27 TAFCD/GW-ME H1612 - 4 Ohm (Black Dome)
40th Ruby DSP8000 and current .2 range. The H1612 first appeared in the Ruby 40th Anniversary DSP8000 and then shortly after in the DSP7200.2. A superb tweeter, offering a wider dispersion with an ‘airy’ open quality,
The H1612 is recommended by Meridian for replacement of the earlier H539 and H1054 tweeters. However the H1612 is more efficient, the lower 4 ohm impedance draws more power and hence has a higher output. This requires access to the DSP loudspeaker “Calibration” menu, decreasing the calibration setting for the tweeter channel by up to -2.5dB. This adjustment gives the loudspeaker a frequency response which follows the same trace as that produced by the original tweeters from the important crossover area up to the 10kHz region. Above 10kHz the H1612 has a slightly different response, so tweeters should be replaced in pairs. You may find the full -2,5dB reduction softens the sound too much. This is dependant upon room acoustics and the age related condition of your loudspeaker. Again experimentation may be required.
The H1612 tweeter and ‘Comms Board’ was previously available as an DSP7200.2 upgrade kit for the DSP7200 but is now obsolete. The H1612 tweeter is currently used in the DSP5200.2, DSP7200.2 and DSP8000.2.
T27BF-ME1 H1703 - 4 Ohm (Beryllium Silver Dome)
The H1703 Beryllium tweeter appears in the SE range launched in 2014 following on from the 40th Anniversary DSP8000 in 2011.
There are two versions of the H1703, the ME1 suffix having small mechanical changes to aid production. An SE upgrade kit had been available since just after the launch of the SE range in 2014 but was unfortunately made obsolete in May 2020. The kit consisted of the H1703 Beryllium tweeter and a complete rear panel SE electronics module.
Accessing DSP ‘Calibration’ menus and subsequent tweeter level adjustment
To access the menu, hold down the “Repeat” key on a Meridian remote while turning on the mains power to the loudspeaker. The display will show: D1 L 65
Then use the right cursor arrow key to select: TW 0.0
Use the down cursor arrow key to adjust this down: TW -2.5 (minus 2.5) for the H1612.
Power off and on the loudspeaker to return it to normal mode with the new adjustment in place. This setting is stored in non-volatile memory and it remains unchanged even if the speaker is re-typed.
The supply and fitment of any replacement tweeter can be undertaken by your Meridian premium partner dealer.



 The current “.2” tweeter can be fitted in place of the original version by using the
“Calibration” menus which are available on all these models of loudspeakers. The relevant setting is user-accessible
and avoids the need for any other hardware changes to the product.
All loudspeaker models fitted with the original tweeter can have it replaced with the “.2” tweeter by decreasing the
calibration setting for the tweeter channel by 2.5dB. This adjustment gives the loudspeaker a frequency response which
follows the same trace as that produced by the original tweeter from the important crossover area up to the 10kHz
region. The two tweeters do have slightly different responses above 10kHz, so tweeters should be replaced in pairs.
To access the menu, hold down the “Repeat” key on a Meridian remote while turning on the mains power to the
loudspeaker. The display will show:
D1 L 65
Then use the right cursor arrow key to select:
TW 0.0
Use the down cursor arrow key to adjust this down to:
TW -2.5 (minus 2.5)
Power off and on the loudspeaker to return it to normal mode with the new adjustment in place.
This setting is stored in non-volatile memory and it remains unchanged even if the speaker is re-Typed. In fact, the only
way to change it is to go back into the menu and change it manually.
Please note, the modification does not cause the loudspeaker to identify itself as a “.2” model when powered up! Please note that you may need to retype after making adjustments in the calibration menu.

The integrated home site went months ago and Stuart has not answered emails. it was a great resource.

Rgds
Stuart

Last edited by StuWils; 2023-11-14 14:44.

Linn LP12, Ittok LV11, Arkiv, Linn Kairn as a phono stage, MPmax 221, DSP6000's, WiiM Pro streamer.