logo

Google Search  |  Meridian Systems  |  Meridian Streaming  |  Restaurant  |  WiKi  |  Duncan's Meridian Info  |  Board Rules  |  Restaurant Rules
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 5 of 12 1 2 3 4 5 6 7 … 11 12
Joined: Jan 2004
Posts: 2,474
Likes: 18
Senior Shouting Officer
Senior Shouting Officer
Offline
Joined: Jan 2004
Posts: 2,474
Likes: 18
Load firmware.
Type it (RTFM).
Then it should start with an ok message again.
Then start legacy program and go from there with a blank/new config.


DSP8000SE, DSP7200SEHC, DSP5200SE sides, DSP7200SE rears, 861v8, 210, Sim2 Ultranero 4, Stewart Cinecurve 2.35:1, XEIT CM-5E Anamorphic lens, Dune HD Duo Cinema 8K and Wireworld Platinum 48G HDMI -> UHD722 -> Shunyata Omega Ethernet. Shunyata/Furutech power-cables/filters. SR Master Fuse@861v8. Uptone Etherregen with 10MHz OCXO clock.
Joined: Aug 2004
Posts: 7,950
Likes: 19
Ian Offline
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: Aug 2004
Posts: 7,950
Likes: 19
You probably just need to retype the unit. It's in the addendum documentation that the unit will display Bad Software and Bad EEPROM at various stages of the upgrade until a retype is performed - see 'choosing a standard setting' in the manual (linked below). This also tells you what legacy config program you should be using which you can obtain by downloading the common installer.

If that does not work, personally I would start from scratch and get to a known good point using default settings.

You can reflash the firmware even if the machine is in a bad way - the flash upload uses a separate BIOS system independent of the firmware to perform the upload so this will be unaffected by the flash upload. However a controller card failure will prevent the reflash but we know this is working as you have already performed a flash upload.

After the reflash, immediately re-type the 568 to the nearest type that suits your configuration - look up TYPE in the manual - you will need to choose the option. The retype is important to do after a firmware update and especially so after the loading the beta firmware as it sets all internal memory locations to known good values for that version of the firmware.

From then, re-read the beta software addendum and undertake any steps that it says paying attention to the calibration of the unit as this will test all channels and you will know that the unit is operating as it should. Instructions about calibrating without a computer are in the 568.2 user manual. You also need to understand the new preset mapping as this is different to the 568. Then connect your sources as per the physical inputs in the manual. You only need to use the config program if you change any of logical/physical input mapping.


Meridian owner since 1992
Prime & PSU, Focal Elear headphones, Roon (ROCK 8Gi5 NUC), Explorer 1 & 2, F80. 200/203, various Sonos (via Roon).
Joined: Sep 2009
Posts: 5,364
Likes: 2
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: Sep 2009
Posts: 5,364
Likes: 2
Nick, he seems to have corrupted his firmware somehow, so he has to mess around with firmware one more time, I suspect.

Good point about the manual. Why didn't anyone think of that? wink


Ex-moderator
Sitting room: dCS Network Bridge, 818v3, HD621, 8kSE
Library: dCS Rossini Apex DAC/Clock, Clearaudio Performance Wood, Audio Research PH2, Mjölnir KGST, Mjölnir PureBipolar
SWMBO Room: 210, D33
Kitchen: Meridian MS200, Genelec 6010 actives
Mobile: Audioquest DragonFly Copper, Sennheiser IE600
Desk: Merging Anubis
Server: Roon/ROCK/NUC

Headphones: Stax SR-X9000, Stax SR-007, Stax SR-404LE, Audeze LCD-X...

Oldest audio file: 1889 Edison cylinder
Joined: Jun 2011
Posts: 133
Hitchhiker
Hitchhiker
Offline
Joined: Jun 2011
Posts: 133
Ian you are correct, I downloaded the update that was sent to me. Unlike the Meridian instructions it did not say �WinFUP.exe�. It was a folder that opened up with six items in it and when I clicked on the first it connected and downloaded all the icons that I saw on the screen except one maked TYPESET or something. But when I clicked on it it said it was incorrect and would not download.

The first time I did the download I did get the "bad software" and after restarting got the "bad EEprom" so I figure all was well. From there I screwed something up using the config flash program.

Anyway I have got back and reloaded the firmware but do not get the "bad software or :bad EEprom" flashing" which concerns me but it sure as hell is not configured so I need to get clear on this "typeing" I think.

Thanks.


G61R, HD621, 3xDSP33 (front, center left), 2xD1500 subs, 2xDSP420 (rears), Sonos everywhere.
Joined: Aug 2004
Posts: 7,950
Likes: 19
Ian Offline
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: Aug 2004
Posts: 7,950
Likes: 19
Retyping is a fundamental Meridian thing. It is their equivalent of a factory reset, except that you get some say on what the initial factory defaults are based on your setup, especially speaker configuration.

Its in the user manual under choosing a standard configuration which is in the configuring without computer section.

Based on 5 x dsp33 and 1 D1500, you probably want to start with type '5.1 DDD' then when you are happy, go back on previous advice regarding integrating your second D1500. Once at standard configuration, you can plug in your sources as per standard source settings a couple of pages further on.

As you have a 562v2, it is likely that most of your sources will be on one of the coax digital inputs which does complicate matters slightly as your 562v2 will be doing the source/input switching before it gets to the 568, but the 568 will still need to be setup to remap the physical inputs of each logical source to the single input that the 562 is connected to. As you seem to be struggling, leave the 562 out of the loop for now just until you are happy with the 568.

Then following the speaker calibration steps using your SPL meter.

Once you are happy that all is well, progress to legacy PC config program to fine tune your settings.

Apologies for any errors in above. Its been a long time since I had a 568.



Meridian owner since 1992
Prime & PSU, Focal Elear headphones, Roon (ROCK 8Gi5 NUC), Explorer 1 & 2, F80. 200/203, various Sonos (via Roon).
Joined: Aug 2002
Posts: 4,579
Likes: 26
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: Aug 2002
Posts: 4,579
Likes: 26
Hi Bayetta,

Sorry, I should have offered more guidance in that email, but I thought you had WinFUP sorted.

There are distinct steps to complete when setting up a processor to your own system. As you wanted to flash the firmware, there's the additional step involving the WinFUP prgramme. If you follow the steps below, you'll get there. I have the legacy programme open in front of me to check this as I type.

1. With the processor connected to the laptop/PC, open WinFUP, and browse to the folder I emailed you. Choose the .mfp file called 568_25b9.mfp. Start the installation process, and don't choose any other file than that one. (when the .mfp file is loaded, it automatically calls up the other .mfu files to load in the correct sequence, so you don't need to do anything further).

2. "Type" the newly flashed processor. This does not involve the laptop/PC or any other programme. It's done from the front panel of the processor, and as Ian says, sets the basic properties of the processor for the number and type of speakers you are using (i.e. DSP or analogue).

3. Reconnect the laptop/PC. Open the legacy configuration programme. If a desktop Icon has been created, it will just be called 'Meridian'. It's the common tool used to set up all the 500 series kit and some DSPs. Create a new file. A dialogue box comes up, which list various products, including '568'. That covers all the 568 variants. Choose 568.

Click on whichever remote you have. This only tells the programme which name label to apply to each of the inputs, as there was some different button labelling between the MSR and MSR+.

On the left, click once on the proccesor symbol. You now have a drop down menu to the immediate right of that to choose which variety of 568 you are setting up. You need to choose "2.50 and higher".

Double click the processor symbol on the left again. You now have some other symbols down the left column. Double click on 'Settings'. This will open up more choices, namely 'Setup', 'Speakers', 'Presets' and 'Sources'. The two of relevance for now are firstly 'Speakers' and 'Sources'.

Choosing 'Speakers', there are a number of tabs along the top, go through each and fill in the appropriate info for your system. When you've done that...

Choose 'Sources', and from the list of sources presented, set them up as appropriate.

4. When you've done all of the foregoing, and with the processor connected, STORE to the product, then save the file on the laptop with a suitable name.

Whew! Right, if you have the wiring connections correct from the processor to your DSPs (including your comms connections, which can present a number of "gotcha' moments!) then you should be ready to start enjoying the music!

Cheers,
George





Joined: Aug 2006
Posts: 761
Likes: 20
Paranoid android
Paranoid android
Joined: Aug 2006
Posts: 761
Likes: 20
Just an additional comment that might be useful, I'm pretty certain my 568.2 needed one or even two power cycles (switch the main power switch on the back of the unit off then on again) the WINFUP program gave instructions as it went along.

I mention it as I the first time I installed the beta software I thought gosh that was quick and it took a moment or two to realise there was more to come.


Main system; 861v8 ID41, DSP8000SEU fronts with DSP5500 centre and DSP7000 rears (all in lovely silver) 504, HD621
Second system 861v4 ID40 LPS, G98DH, 504, HD621, 2x DSP5200 with DSP5200 centre
MD600 tucked away in study. Lots of other Meridian!
Joined: Jun 2011
Posts: 133
Hitchhiker
Hitchhiker
Offline
Joined: Jun 2011
Posts: 133
Well now I think we might be getting somewhere.

2 questions:
After entering type I did not power cycle the processor. Is that right or am I to restart?

In the speaker config, I have DSP1500 subs. There are 3 settings to make:
- Music
- Logic
- 5.1 Movie

Do I choose "two left-right for all?

I went ahead and made some choice as I know they can be changed.

Could it be that USR to RS232 adaptor chipset issue but it took a few restarts before it said "loaded successfully" but a concern in the dialogue box it shows all green checks except one blue exclamation saying "Product BIOS is Meridian 568, version 2.01." Not sure what thats about. When I turned the 568 off/on then it unfortunately flashed "bad software". I thought we were there.

It's 1:00 am going to bed.


G61R, HD621, 3xDSP33 (front, center left), 2xD1500 subs, 2xDSP420 (rears), Sonos everywhere.
Joined: Jan 2004
Posts: 2,474
Likes: 18
Senior Shouting Officer
Senior Shouting Officer
Offline
Joined: Jan 2004
Posts: 2,474
Likes: 18
Yes, Two - Left/Right sounds like the stereo sub choice. Select this setting for all music/film modes.

Speaker size for the D1500 shoould be 'MAX' and not some number.

Also if there is a THX capable setting (flat response to 20Hz) select that as well.

Also check your subs so that they don't roll off or anything on the physical cabinet electronics.

What are your settings on the D1500 subs?


DSP8000SE, DSP7200SEHC, DSP5200SE sides, DSP7200SE rears, 861v8, 210, Sim2 Ultranero 4, Stewart Cinecurve 2.35:1, XEIT CM-5E Anamorphic lens, Dune HD Duo Cinema 8K and Wireworld Platinum 48G HDMI -> UHD722 -> Shunyata Omega Ethernet. Shunyata/Furutech power-cables/filters. SR Master Fuse@861v8. Uptone Etherregen with 10MHz OCXO clock.
Joined: Sep 2009
Posts: 5,364
Likes: 2
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: Sep 2009
Posts: 5,364
Likes: 2
The D1500 can't be configured beyond the switches on the back. It has no RS232 port.

The input switch (1, 1&2, 2) needs to be correct so that they actually play L and R correctly. I don't however know the settings in his case (as I only have one). The manual will tell him that. wink

The crossover switch needs to be Flat (not Filter 1 or Filter 2) because the processor will be handling the crossover.

The gain knob will be relevant. I suggest he adjusts it by ear before calibration, then the calibration process will really only be fine-tuning his setting by ear.


Ex-moderator
Sitting room: dCS Network Bridge, 818v3, HD621, 8kSE
Library: dCS Rossini Apex DAC/Clock, Clearaudio Performance Wood, Audio Research PH2, Mjölnir KGST, Mjölnir PureBipolar
SWMBO Room: 210, D33
Kitchen: Meridian MS200, Genelec 6010 actives
Mobile: Audioquest DragonFly Copper, Sennheiser IE600
Desk: Merging Anubis
Server: Roon/ROCK/NUC

Headphones: Stax SR-X9000, Stax SR-007, Stax SR-404LE, Audeze LCD-X...

Oldest audio file: 1889 Edison cylinder
Joined: Jun 2011
Posts: 133
Hitchhiker
Hitchhiker
Offline
Joined: Jun 2011
Posts: 133
I'lll give you the sub settings tonight.

But still if it "successfully loaded" when I hit "store" than why the "bad software" on restart. Is the 2.5 firmware the only software the processor uses? Could the software (not the firmware update) be corrupted? I have no 568.2mm install discs.

Kinda baffling as I really thought we were there.


G61R, HD621, 3xDSP33 (front, center left), 2xD1500 subs, 2xDSP420 (rears), Sonos everywhere.
Joined: Aug 2002
Posts: 4,579
Likes: 26
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: Aug 2002
Posts: 4,579
Likes: 26
Hi Bayetta

I'm struggling a bit (as I suspect others are too) to get a grasp of where you're coming unstuck, and I think it's because you're being too vague in your answers, and raising several variables at once.

Can you confirm which of the steps outlined above (by each of us) that you've successfully completed? It would be useful to know what variance you've had in behaviour/display of the 568.2mm to each of the anticipated outcomes which we've described.

Cheers

George

Page 5 of 12 1 2 3 4 5 6 7 … 11 12

Moderated by  Carl, Duncs, ncpl 

Link Copied to Clipboard
Who's Online Now
3 members (OldDogCan, JCD, bxd), 767 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Newest Members
Kiran1103, Tony999, PhilP, Grover, Humberto
5,503 Registered Users
Top Posters(30 Days)
HugoF 10
Ludwig 8
Top Posters
VirusKiller 12,733
ncpl 8,816
Carl 8,506
Fiddler 8,364
Ian 7,950
Forum Statistics
Forums18
Topics31,254
Posts297,477
Members5,503
Most Online4,788
May 22nd, 2026
Meridian  |  Media Centre  |  Support  |  Firmware Release Notes  |  RSS Systems  |  RSS Streaming  |  RSS Restaurant

Website Provided by Mr Tech Guy - Resolute Audio Visual Limited © 2026

Powered by UBB.threads™ PHP Forum Software 8.0.1
(Release build 20251126)
Responsive Width:

PHP: 8.5.13 Page Time: 0.059s Queries: 39 (0.047s) Memory: 0.7033 MB (Peak: 0.8055 MB) Data Comp: Off Server Time: 2026-11-20 14:06:32 UTC
Valid HTML 5 and Valid CSS