logo

Google Search  |  Meridian Systems  |  Meridian Streaming  |  Restaurant  |  WiKi  |  Duncan's Meridian Info  |  Board Rules  |  Restaurant Rules
Previous Thread
Next Thread
Print Thread
Rate Thread
#122000 2010-08-01 16:41
Joined: Apr 2008
Posts: 52
Mostly harmless
Mostly harmless
Joined: Apr 2008
Posts: 52
Has anyone out there got any ideas on the follwing?

My 'new' 800, which sounds absolutely superb, will not respond to any movement controls from the MSR+.
It will respond N Controller to clear, it will switch on and off.
The display will change when display is pressed, but it will not start, stop, skip or respond to numbers.

I know I need the exercise but I'd rather not continue getting up and down.

Any thoughts gratefully accepted!


861v8, 2 x 5200SE 5200SEHC, UHD722, Oppo 203EU, Panasonic UB820, PS3.
Joined: May 2008
Posts: 8,506
Likes: 78
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: May 2008
Posts: 8,506
Likes: 78
Hi Harry,

Here's a quick check list; have you:

-- Connected up a DIN C5 comms lead to it (sorry but I have to ask)?
-- Edited you M-config config and added the 800 into it?
-- Checked that the "comms type" is correct in M-config?
-- Typed it, and then downloaded this new M-Config in to it?

Then press "clear" when all is in standby to make sure on the your G68 is a controller.

Does the volume display on the 800 keep in sync when you change volume:
1) With the MSR+ 2) From G68?

Give me a call at home, if you wish, I'm in all day today.
But don't tell me the F1 race results, I'm about to watch a recording of it.

Regards,
Carl


861v6+ID40, HD621, 8000.2, 7200HC, 7200.2, SKYQ Silver, PS3, PDP-LX6090, QNAP TS870-Pro (8*6TB), Roon, iPadAir2.
[In Reserve] C15, MD600 (2*3TB), TwinStore RM (2*2TB)
Joined: Apr 2008
Posts: 52
Mostly harmless
Mostly harmless
Joined: Apr 2008
Posts: 52
Hi Carl,

I understand where you're coming from with the questions

Com cable - Yes
M Config - Yes and saved to the G68
Comms type ???? - I need to look
Typed the 800 as type zero.

I can't save the M-Config on the 800, it falls over on room correction data

I've not looked at the volume display on the 800 - I'll go and have a look.

The pleasures of M-Config - I've go and have a review!

Thanks for the advice!




861v8, 2 x 5200SE 5200SEHC, UHD722, Oppo 203EU, Panasonic UB820, PS3.
Joined: May 2008
Posts: 8,506
Likes: 78
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: May 2008
Posts: 8,506
Likes: 78
Originally Posted by Harryp
I can't save the M-Config on the 800, it falls over on room correction data

Very odd! Are you trying to download the G68 setup to the 800?

In M-config, click on the 800 and then select download config.

BTW: What version of the 800 did you get?
And make sure if it is an 800D you use the 800D source in M-config and not 800.

Carl.


861v6+ID40, HD621, 8000.2, 7200HC, 7200.2, SKYQ Silver, PS3, PDP-LX6090, QNAP TS870-Pro (8*6TB), Roon, iPadAir2.
[In Reserve] C15, MD600 (2*3TB), TwinStore RM (2*2TB)
Joined: Apr 2008
Posts: 52
Mostly harmless
Mostly harmless
Joined: Apr 2008
Posts: 52
Hi Carl,

I believe it's a D.
It has HDMI output.
It says 800 on the front.
Is there somewhere where the D is specified?

Harry


861v8, 2 x 5200SE 5200SEHC, UHD722, Oppo 203EU, Panasonic UB820, PS3.
Joined: Apr 2008
Posts: 52
Mostly harmless
Mostly harmless
Joined: Apr 2008
Posts: 52
OK - here's logic for you.

I'd been using the steps across the top of M-Config, rather than clicking on the 800 and store.
It fell over in exactly the same manner - did not receive OK,
Store not successful.
The 800 would then not read disks or works at all - exactly as last time.
Reset the 800 to type 0.

So I have followed the exact path as before.

And guess what!

It now works perfectly.

The pleasures of M-Config.

Thanks for your help Carl!

Enjoy the race!!!


861v8, 2 x 5200SE 5200SEHC, UHD722, Oppo 203EU, Panasonic UB820, PS3.
Joined: May 2008
Posts: 8,506
Likes: 78
President of the Imperial Galactic Government
President of the Imperial Galactic Government
Joined: May 2008
Posts: 8,506
Likes: 78
Cool,

If a config load continues to fail try increasing the delay in M-config communication options as this can help.

800v3 Has 3*SPDIF SmartLink but no HDMI, so you must have a v4 spec or 800D.
800v4 Has HDMI and the back panel is made up of individual cards.
800D Same spec as v4 but the back panel is made up of just 2 large cards.

The serial number tells you what version the 800 was when built.
If is starts with a 4 you know it is an original v4 or 800D.

Pleased all is now well.

Regards,
Carl


861v6+ID40, HD621, 8000.2, 7200HC, 7200.2, SKYQ Silver, PS3, PDP-LX6090, QNAP TS870-Pro (8*6TB), Roon, iPadAir2.
[In Reserve] C15, MD600 (2*3TB), TwinStore RM (2*2TB)

Moderated by  Carl, Duncs, ncpl 

Link Copied to Clipboard
Who's Online Now
0 members (), 528 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Newest Members
Kiran1103, Tony999, PhilP, Grover, Humberto
5,503 Registered Users
Top Posters(30 Days)
HugoF 10
Gemeni 8
Top Posters
VirusKiller 12,733
ncpl 8,816
Carl 8,506
Fiddler 8,364
Ian 7,950
Forum Statistics
Forums18
Topics31,253
Posts297,455
Members5,503
Most Online4,788
May 22nd, 2026
Meridian  |  Media Centre  |  Support  |  Firmware Release Notes  |  RSS Systems  |  RSS Streaming  |  RSS Restaurant

Website Provided by Mr Tech Guy - Resolute Audio Visual Limited © 2026

Powered by UBB.threads™ PHP Forum Software 8.0.1
(Release build 20251126)
Responsive Width:

PHP: 8.5.12 Page Time: 0.033s Queries: 29 (0.028s) Memory: 0.6515 MB (Peak: 0.7083 MB) Data Comp: Off Server Time: 2026-11-18 06:43:25 UTC
Valid HTML 5 and Valid CSS