George,
after reading your post, I understand that this -3dB is needed for the headroom and center level in the different presets.
Why M have a positive dB adjustment for the center I dont know, I mean the center speaker is allways louder as the mains and have to be calibrated lower .
Subtracting 3bit from the original signal reduces the theoretical dynamics.
Having 96dB on the CD as a maximum and 0dB as a minimum,you get "only" 93dB after the prozessor.
But you cant compare this 1:1 to the practical dynamic at your home.
The dynamic at home are limited in the maximum SPL for your ears and your equipment,
and at the minimum level for the ambient noise.
So have maximum 100dB(thats really loud), your rooms have at least 40dB ambient noise,maybe with luck only 35dB.
So your practical dynamics are 100 minus 40(35) means 60(65)dB.
So the (bit) dynamics from your CD get "scaled" to a SPL dynamic of 60dB.
When you loose 3db from 96dB you have a new scale from 93 to 60 dB instead of 96 to 60dB.
You can imagine that this is not a big difference on the paper.
And the most important thing is, this dynamics you will only get when you turn the volume nearly full up,
so the 0dB (full scale) from your CD get to 100dB SPL.
If you dont listen to this nearly full up volume, you will loose dynamics again.
But how its sound ?
I testet only in stereo with two 8k and stereo preset.
I get a test record from Nippon Columbia (Denon) C39-7147 with a lot of usefull test signals on it.
First I want to test when the DSP get digitally saturated.
There are different frequencies with full scale means 0dB on it.And you have that for L and R channel,
so you can test it independly.
So I modified the configfile with the text editor as George described.
The only difference is that I let one channel at 0 dB, so I can compare easily with just jumping to the next track.
For example the L speaker is calibrated to 0dB and the right one to +3dB.
As the CD have tracks for each channel you can skip between the tracks and compare it with your ear.
As you put +dB in the file the output of the prozessor get louder and regarding to impressions it correspond with the volume display-means 3dB more positive you have to subtract 3 units from the volume display to get the same SPL.(Sorry have only my ears no SPL meter).
So I dit make some files with left 0dB and right starting with +15dB down to 3,5 dB.
Then I listen with skip the tracks between the different dB levels.
I can clearly hear when the DSP is digitally saturated.
Its easy to hear it with 1kHz and with 10kHz.
With 1kHz the frequency stays at the same as expected, but the overtones? are different.
Its like when you hear a guitar or mandoline play the same note(same frequency) but it sounds different.
With 10kHz have to pop the volume a little to hear the 10kHz and maybe turn the head a little until you will hear it.But the good thing on that is that this more sensitive as the 1 kHz tone.With 10kHz you hear a second tone with a different(lower) frequency when the signal is saturated.
So I found out that + 3.5 dB saturated the sound and 3.0 dB not.
Its a good test to modify with higher positive dB maybe 9 or 12 to easily get the impression how a saturated signal sounds.
So I finally use two file with 0dB(L&R) and +3dB(L&R) to make a sound test with a very well known CD.
I dit change that 3 times to get shured about my impressions.
The sound with +3dB (play with 3 volume increments lower) seems to smoother with voices maybe even smoother when the voices are at low levels.The piano and accustic instruments sound a littler more "natural" with a little more body.
I will test more on that with different recordings so I can describe that better and check that Iam not "head pregnant".....
I also will test this +3dB thing with DVDA to find out how that will be sound.
George thanks for playing and testing to found that out, I allways thinking its just 3dB lower volume what can be corrected with the volume knob.But its definetly more.
The bad thing is, that the center cannot adjusted to that +3dB, as then the speaker is to dominate.
I have before all that testing the L/R at 0dB and the center at -1.5dB.
When I now calibrate the center also to +3dB, the speaker is to loud.Of coarse you can adjust the level of the center in that presets where a seperate center level adjustment is,but what are you doing with the other presets where no extra center level adjustment is?
That means, that in that preset the center is to loud.
So only two possibilities are left:
a)Calibrate the center to +1,5dB(in my case with 1.5dB difference between the mains and center) and the mains to +3dB.
b)Adjust L/R/C to +3dB and listen only to that presets where you can adjust the center level in the preset(to 1.5dB in my case)
George it would be interesting now to compare the sound of the DSP with direct plug in a CD transport in the speaker and going through the prozessor as there should be no SPL difference.
But this issue is something what M should remove immediately. Its a minor thing for them and the system sounds better.
thanks George
Robert
800v3/218/271/8k.2/5k5s

/5kC/DSP3200/Reviver/
TT-ELP/Graham Slee Revelation/Trinnov Altitude 32/OPPO 205
__Ayon/HB/Shunyata/Miltzow -- power cables,
__Ayon/Jungson/Miltzow --analog, Miltzow-- digital,
__Vortex/WMA ,