|
|
Joined: Nov 2001
Posts: 691 Likes: 4
Formerly Meridian506 Paranoid android
|
|
Formerly Meridian506 Paranoid android
Joined: Nov 2001
Posts: 691 Likes: 4 |
Meridian DOES NOT use that Hybrid Special sauce for doing CHANNEL level adjustments in the processor (with DSP Speakers). It only uses it for Master Volume. So the processor is doing the level adjustment on its digital outs? When you get time to get your Tascam out can you verify that the streams on FL/FR are different from SR/SL? (Maybe mono preset party mode is a good test for this, since it should be the same stream on each channel just with level adjustment) If this is the case, then why the Meridian Digital Theater Type in the speaker setup and also not fix this when they added the G series comms mode to the speakers? Didn't Bob say he'd be willing to answer questions if Stacey or someone organised them?
Living room: DSP5000.3 WFH Office: M33 Bedroom: P200ZQ
|
|
|
|
|
Joined: May 2000
Posts: 8,364 Likes: 14
President of the Imperial Galactic Government
|
|
President of the Imperial Galactic Government
Joined: May 2000
Posts: 8,364 Likes: 14 |
So the processor is doing the level adjustment on its digital outs? YES !!! When you get time to get your Tascam out can you verify that the streams on FL/FR are different from SR/SL? (Maybe mono preset party mode is a good test for this, since it should be the same stream on each channel just with level adjustment) Not sure what your saying here. If this is the case, then why the Meridian Digital Theater Type in the speaker setup and also not fix this when they added the G series comms mode to the speakers?
Didn't Bob say he'd be willing to answer questions if Stacey or someone organised them? We've never got real far with deep questions like this. Anyone recall Trifield width or the last time we asked about Ron's observations. I'd really like folks to confirm if they hear an audible improvement before even considering asking a question. Keep in mind Meridian may standby the choice (even if there is some compromise)and may not consider it problem. The headroom may be needed to handle the variety of configurations. I think it's partly a limitation in how DSP speaker communication is setup (designed well before home theater that needs indvidual channel adjustment). Two Channel didn't need it.
- Fiddler (IMHO)
If you think listening to music is fun, try learning an instrument. HT: G61RSL, 4x5K, 5.5KHC, 2xSC6000, Transporter, HD621, Philips BDP7501 4K, Tivo, 65" LG OLED 4K C6 Computer: Foobar2000, 5K, Mojo, HiFiMan HE1000 V2
|
|
|
|
|
Joined: Apr 2004
Posts: 12,733 Likes: 88
Don't Panic!
|
|
Don't Panic!
Joined: Apr 2004
Posts: 12,733 Likes: 88 |
Still waiting for the answers to the questions submitted at the HH2 event...
|
|
|
|
|
Joined: Apr 2004
Posts: 12,733 Likes: 88
Don't Panic!
|
|
Don't Panic!
Joined: Apr 2004
Posts: 12,733 Likes: 88 |
George. Have you compared direct into your 6ks vs. through the G68 at 0dB calibration and +3dB volume vs. direct?
|
|
|
|
|
Joined: Feb 2003
Posts: 146
Hitchhiker
|
|
Hitchhiker
Joined: Feb 2003
Posts: 146 |
George - super stuff!
I could not resist doing "+3.0db across the front mod" and I'm listening tho' the 861v4 with theas I type - it works a treat! Early critical listening seems to indicate 'better but not QUITE as good as straight-through', via 861 (Direct DSP mode, no MRC) vs. 808i.2 - 8000s.
Not only does this seem to solve the -3.0db 'attenuation through the processor' issue, but it sorts out another thing that's been nagging me for a long time - (my perception of) audible 'steps' in amplification 'noise' across the volume range. These seem (to my ears) to occur at the 73 - 74 and 79-80 boundaries (I notice the slightest of 'clicks' as I step through if listening carefully). 73 and below is quieter than above and the "3.0db mod" enables me at 73 instead of my normal 76 - 77 level. Without wishing to highjack George's execellent thread, I would be interested to hear if anyone else notices this effect.
All in all George's effects have defo unlocked benefits for me.
Andy
System 1: Control 15, 818v3, 800v3, 861v6, DSP8000SE, DSP7200HCSE, DSP8000.2, SW5500, HD621, 650BD, SkyHD, Radience XE, TH65PF12 System 2: MS200, 5200 System 3: MS200, F80 Sooloos: MD600: 2x3TB On the move: Explorer 2, B&W P7W Bedroom: F80+i80
|
|
|
|
|
Joined: May 2000
Posts: 2,534
Great Green Arkleseizure
|
|
Great Green Arkleseizure
Joined: May 2000
Posts: 2,534 |
Any chance that adding 3db gain will result in digital clipping on loud passages?
561, DSP5500s, DSP5000C, analog sides and rears
|
|
|
|
|
Joined: Apr 2004
Posts: 12,733 Likes: 88
Don't Panic!
|
|
Don't Panic!
Joined: Apr 2004
Posts: 12,733 Likes: 88 |
We talked about that on the 1st page Frank.  Definitely a possibility.
|
|
|
|
|
Joined: May 2000
Posts: 8,364 Likes: 14
President of the Imperial Galactic Government
|
|
President of the Imperial Galactic Government
Joined: May 2000
Posts: 8,364 Likes: 14 |
George. Have you compared direct into your 6ks vs. through the G68 at 0dB calibration and +3dB volume vs. direct? Yes. That is exactly my reference point and partly what drove this. I can Run Transporter Direct to DSP-6000's (via Zone 2 on G68) D2 (Direct DSP Preset) I can Run Transporter Direct to DVDO to HD621 (via Zone 2 on G68) D2 (Direct DSP Preset) I can Run Transporter Direct to G68 (Direct DSP Preset) I can Run Transporter Direct to DVDO to HD621 to G68 (Direct DSP Preset) I do all the switching with one click on the remote. No moving cables no delay. Only one extra cable. Zone 2 Dig Out to DSP-6000 Master D2. Same for PS3. All done with phantoms, zones, and D1 vs D2. All sound identical and levels measure identical with a calibration BD disc. I'm almost out phantoms  Zone 2 is an exact copy of what goes in. No processing is ever applied. I tested that thoroughly in the past. Recording DTS through it and playing back. And diffing recordings through it.
- Fiddler (IMHO)
If you think listening to music is fun, try learning an instrument. HT: G61RSL, 4x5K, 5.5KHC, 2xSC6000, Transporter, HD621, Philips BDP7501 4K, Tivo, 65" LG OLED 4K C6 Computer: Foobar2000, 5K, Mojo, HiFiMan HE1000 V2
|
|
|
|
|
Joined: May 2000
Posts: 8,364 Likes: 14
President of the Imperial Galactic Government
|
|
President of the Imperial Galactic Government
Joined: May 2000
Posts: 8,364 Likes: 14 |
Frank deleted a post I was replying too. But it brought up an important point.
If front 3 are not the same levels now (before applying tweak) you need to make some choices.
If my left and right front are different I would ignore that and set them both to +3.0db (that's your "LevelPerfect" anchor on your most critical speaker). I think it's important to get EXACTLY +3.0db on the mains (ideally all fronts, but for some folks center will be too different). But for most folks left and right should be close enough to make them the same. If you hooked a CD player or Tranporter direct you would not get any calibration. It's not a big deal.
If you feel center is most critical set that to +3.0db.
In my case I was -3.0, -3.5 and -3.0 and I set them all +3.0db and said screw the center being off by .5db I my rears were -1.0 so I had to set those to +5.0db to maintain a proper level.
- Fiddler (IMHO)
If you think listening to music is fun, try learning an instrument. HT: G61RSL, 4x5K, 5.5KHC, 2xSC6000, Transporter, HD621, Philips BDP7501 4K, Tivo, 65" LG OLED 4K C6 Computer: Foobar2000, 5K, Mojo, HiFiMan HE1000 V2
|
|
|
|
|
Joined: May 2000
Posts: 8,364 Likes: 14
President of the Imperial Galactic Government
|
|
President of the Imperial Galactic Government
Joined: May 2000
Posts: 8,364 Likes: 14 |
George - super stuff!
I could not resist doing "+3.0db across the front mod" and I'm listening tho' the 861v4 with theas I type - it works a treat! Early critical listening seems to indicate 'better but not QUITE as good as straight-through', via 861 (Direct DSP mode, no MRC) vs. 808i.2 - 8000s.
Not only does this seem to solve the -3.0db 'attenuation through the processor' issue, but it sorts out another thing that's been nagging me for a long time - (my perception of) audible 'steps' in amplification 'noise' across the volume range. These seem (to my ears) to occur at the 73 - 74 and 79-80 boundaries (I notice the slightest of 'clicks' as I step through if listening carefully). 73 and below is quieter than above and the "3.0db mod" enables me at 73 instead of my normal 76 - 77 level. Without wishing to highjack George's execellent thread, I would be interested to hear if anyone else notices this effect.
All in all George's effects have defo unlocked benefits for me.
Andy Thanks Andy for giving it a go. Comparing an 808.2i is a little unfair though  I'm sure the 808.2i has some extra special sauce going through anything less than an 861V6 might lose something (even with this tweak). Yes I have heard those clicks at certain points. I believe this is the hybrid volume in the DSP speaker at work. What did you end up setting rears/sides from and too? Do you have 808.2i hooked direct to 8K's and to 861 normally?
- Fiddler (IMHO)
If you think listening to music is fun, try learning an instrument. HT: G61RSL, 4x5K, 5.5KHC, 2xSC6000, Transporter, HD621, Philips BDP7501 4K, Tivo, 65" LG OLED 4K C6 Computer: Foobar2000, 5K, Mojo, HiFiMan HE1000 V2
|
|
|
|
|
Joined: May 2000
Posts: 2,534
Great Green Arkleseizure
|
|
Great Green Arkleseizure
Joined: May 2000
Posts: 2,534 |
I just went in the MSL file with notepad and set my front 3 speakers to +3db (in hex, the +3db value is 0x26). I am going to have to add +3db to each of the existing speaker calibration levels in my .msl file. How do I go about calculating the hex value of -0.5db or +2.5db for example. In the hex conversion calculator I found on the web, it said 0x26 was equal to 38 not 3.
561, DSP5500s, DSP5000C, analog sides and rears
|
|
|
|
|
Joined: Nov 2001
Posts: 691 Likes: 4
Formerly Meridian506 Paranoid android
|
|
Formerly Meridian506 Paranoid android
Joined: Nov 2001
Posts: 691 Likes: 4 |
When you get time to get your Tascam out can you verify that the streams on FL/FR are different from SR/SL? (Maybe mono preset party mode is a good test for this, since it should be the same stream on each channel just with level adjustment) Not sure what your saying here. If you can record the digital outputs (like you do for SACD rips), then Party mode under the Mono DSP preset will send the same signal (but level adjusted) to each channel so that you can prove that the level adjustment is taking place in the processor. With an appropriate test tone you should be able to measure/see the distortion introduced by the G68. Makes you wonder why they are using 0.5 bits instead of a whole bit shift to get the headroom.
Living room: DSP5000.3 WFH Office: M33 Bedroom: P200ZQ
|
|
|
|
1 members (Els),
403
guests, and
4
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums18
Topics31,249
Posts297,435
Members5,503
| |
Most Online4,788 May 22nd, 2026
|
|
|
|