Google Search  |  Meridian Systems  |  Meridian Streaming  |  Restaurant  |  WiKi  |  Duncan's Meridian Info  |  Board Rules  |  Restaurant Rules
Page 2 of 2 < 1 2
Topic Options
Rate This Topic
#270994 - 2017-12-23 03:54 Re: Zone disappearing [Re: Gianni]
Registered: 2016-11-14
Posts: 9
Mark42 Offline
Harmless
Mark42 Offline
Harmless

Registered: 2016-11-14
Posts: 9
Loc: Sydney, NSW, Australia
Problem occurs both with TouchPC and ControlPC .
At one stage I uninstalled ControlPC and re-installed, no difference, ergo me thinks it would be fruitless to uninstall & reinstall TouchPC

Thanks anyway


MN
Top
#270998 - 2017-12-23 09:10 Re: Zone disappearing [Re: Ian]
Registered: 2016-11-14
Posts: 9
Mark42 Offline
Harmless
Mark42 Offline
Harmless

Registered: 2016-11-14
Posts: 9
Loc: Sydney, NSW, Australia
Hello Ian

Have discovered some things you may be interested in.

1 Turning off power on 808v6 does not reset ID41
2 Removing power cable on 808v6 does not reset ID41
3 Have 808v6 in standby and press & hold 'repeat' key on front panel until 'Audio endpoint reset' appears on display ... ID41 is then reset.
4 TouchPC for the first time (for me anyway) allows me to set a Master zone (808v6)
5 /debug as you explained above now shows MC200 'is slave' Yes , 808v6 shows 'is slave' No.

Tested issue

Not resolved.

Manually 're-typed' 808v6 from front panel (type = 1 and ir = controller)

Issue resolved.

However, manually typing clears any configuration changes already set.

So back to MConfig, add MC200 and original issue reappears, I'm now going through every setting on adding MC200 to see what causes problem.

Getting there

Mark


MN
Top
#270999 - 2017-12-23 10:36 Re: Zone disappearing [Re: Mark42]
Registered: 2009-11-10
Posts: 1,271
CMB Integrations - Bruce Offline
Meridian Partner Working on the ultimate question
CMB Integrations - Bruce Offline
Meridian Partner
Working on the ultimate question

Registered: 2009-11-10
Posts: 1,271
Loc: Lexington, South Carolina, USA
You said the MC200 was only connected via ethernet. That said, why would you be adding the MC200 in mconfig? There lies the problem, you have two Sooloos sources in the same mconfig and one is cancelling the other out. I would bet that after everything is reset, and the ID41 is showing up, the ID41 disappears right after it is selected as a zone. I have seen this before.


www.cmbintegrations.com

Personal System #1 Theta Digital Cassablanca 4, 218, DSP8000.2SE, DSP7200SEHC, Revel F228be, Revel B112, Monitor Audio Silver 10, ATI 200WX5 Amp, JVC RS15, Shunyata Denali 600S, Black Diamond Zero Edge screen. QNAP TS-251 3TB
Mark Levinson No515 Turntable

Crestron control and multi room audio via Meridian 258 amplifiers.
Top
#271002 - 2017-12-23 11:41 Re: Zone disappearing [Re: CMB Integrations - Bruce]
Registered: 2016-11-14
Posts: 9
Mark42 Offline
Harmless
Mark42 Offline
Harmless

Registered: 2016-11-14
Posts: 9
Loc: Sydney, NSW, Australia
My mistake, Bruce, MC200 still connected via digital coax to D2 on 808v6, which is why I used MConfig to configure.
I'm adding 1 analogue input at a time, saving msl file as I go so I can restore latest setup if needed. I use MSR to control other devices so the source keys have to be disabled on 808. So far though all works fine without adding MC200 via MConfig.


MN
Top
#271003 - 2017-12-23 11:51 Re: Zone disappearing [Re: Mark42]
Registered: 2010-12-09
Posts: 3,297
Ratbert Offline
Hooloovoo
Ratbert Offline
Hooloovoo

Registered: 2010-12-09
Posts: 3,297
Loc: Europe
So you are not using the ID41 on the 808v6?


Always learn from the mistakes of others. You can never live long enough to make them all yourself.
Top
Page 2 of 2 < 1 2

Moderator:  Carl, Duncs, ncpl 
Who's Online
7 registered (Jeje, JCD, ncpl, Mr Meridian, JimK, Rolski), 47 Guests and 2 Spiders online.
Key: Admin, Global Mod, Mod
Newest Members
NWD73, HenkHaas, GrahamAvison, JimO, sv1dpp
4618 Registered Users
Top Posters (30 Days)
Ratbert 63
Rick415 49
Laserblues2 35
CMB Integrations - Bruce 33
Carl 32
Top Posters
VirusKiller 12298
Fiddler 8671
ncpl 8411
Carl 7647
Ian 7420
Forum Stats
4,618 Registered Members
17 Forums
24,675 Topics
252,777 Posts

Most users ever online: 211 @ 2015-05-05 14:40
Meridian  |  Media Centre  |  Support  |  Firmware Release Notes  |  RSS Systems  |  RSS Streaming  |  RSS Restaurant